Jump to content

lmorris

Members
  • Posts

    2,456
  • Joined

  • Last visited

Everything posted by lmorris

  1. Mustang owners are never happy with any service performed to their vehicle. Someone else installed a short throw shifter incorrectly. I had to remove the transmission to replace a loose shift damper and installed the shifter correctly....and I'm the asshole🤪.
  2. The Isolation Meter detects insulation resistance up to max. 8 GΩ (with auxiliary voltages of 250, 500 and 1000V). In addition, this Isolation Meter offers a measuring function for DC and AC voltages up to max. 950V DC and 700V AC as well as resistors up to max.
  3. 2014 Focus, we finally have TCM's in stock!!!
  4. They just kept on driving it. It chewed up the housing eventually. They only brought it in because it no longer moved.
  5. I would have to say that something has been sucked into the pump at some point and is plugging the inlet.
  6. I will definitely look into that before winter. Thanks. Sure did, had the valve cover off and made sure everything was clean. This thing has 240,000 KMs on it now. It uses a litre of oil per tank of fuel in the city. Not so much on long highway trips though. I am assuming a combination of the crappy oil ring set up and the throttle closing on decel.
  7. It's hard to explain. You have to try to install the ELD carrier with the tabs 180° out to be able to visualize the issue . The tabs are off set and it only goes in one way.
  8. With enough determination, anything is possible. Here's the proof.
  9. For the first time in forever, I worked Dec 26. The entire Dealership was open till 3:30.
  10. Have my wife's 2011 GMC Terrain in my bay currently. Last Thursday the PCV froze up and blew out the rear main seal. Managed to get that replaced over the weekend. Today I had it in cleaning out the PCV system. The tiny hole in the center plugs up and causes all kinds of issues.
  11. Could just be self testing the fan clutch. I didn't think the 6.4L did this, bit maybe.
  12. I was having a discussion with an electrician awhile back when having A/C installed in my house. He asked me if I was planning on getting a hot tub or electric vehicle in the near future. Turns out that most houses are not set up electrically to handle the extra load of a 220V charging station. Most city infrastructures are also not set up. There is going to be some major reworking to accommodate a raise in electric vehicles on the road.
  13. Came in with an oil leak. Leaked faster than you could poor it in the engine. Leaking down the valley from the oil cooler to block seam. Removed the oil cooler and found the cavity full of crud. Bottom of the cooler looks like this.
  14. I can hear it now. "Sir, your 2014 Superduty has a check engine light on, it's the DEF heater. We'll get that done right away!!"
  15. Are you sure that's not going to lead to premature and possibly inaccurate diagnosis? Every time I see an advisor get a hold of a scan tool, it goes sideways.
  16. Now I'm starting to think I heard it wrong. $8 a gallon does seem high. Even for premium fuel.
  17. How. Much has your energy bill gone up? Ours has risen because the cost to produce it has gone up. We are supposed to be getting a tax break starting the April 1. The cost of gas and electricity are supposed to have the provincial taxes removed temporarily. A friend of ours in Camas Washington says they pay $8 a gallon!! That's crazy.
  18. We are $1.64 currently, was at $1.77 yesterday. Our beloved Alberta Premiere is supposed to drop the tax on fuel April 1, for a 13 cent drop.
  19. So, if I unplugged the MAF sensor and rechecked codes, would the P1247 go away if it was the cause? I must add that Prodemand was absolutely no help, both the 98 and 99 wiring diagrams for the ECU were wrong. Had to check we each pin till I found the right one. Turns out one wire is a shared VREF with 6 other sensors. Wiring is good. I wonder if one of the other sensors is messing with the signal.
  20. I have visited the site a few times and agree, the information is abundant. I am astounded by all the crazy fixes for seemingly unrelated concerns. I haven't load tested from the ECU yet as Prodemand seems to be wrong on some of the wiring. IE, it shows the horn button on the wiper arm and not the steering wheel.
  21. My son picked this beast up from a buddy to drive around, he recently had his ride written off. It has no boost and keeps setting P1247. I have access to Prodemand and have checked resistance of the needle lift sensor, 83 ohms. Spec is 80 to 120. Checked for voltage to the sensor and get 5 volts using battery ground. I get 3.2 volts when using the PCM ground. I read it was supposed to run 3.2 volts from the PCM. Checked all connections and found no issues. The diagnosis ends with replacement of the PCM. Given this is a free vehicle, we don't want to start throwing expensive and hard to get parts at this thing. My son is content with putting up with the lack of power, but I would like to try and fix it, if possible. If anyone has any VW Diesel experience, I would appreciate any input. Thanks.
  22. You are correct. The outer edge of the flexplate is the tone ring.
  23. Pull the crank sensor and inspect the tone ring on the flywheel. If you already haven't. We had one that would just quit for no reason, turned out the tone ring was rusty and there was a chunk of metal on the sensor.
×
×
  • Create New...