All Activity

I had one similar to this about 2 years ago, it was a fire rescue unit, I had to do 3 turbos before I got a good one. I ended up cracking them open and the unison ring was warped in the first 2 reman replacement turbo's if I remember correctly. Sounds the same though, I remember having to get it fully warmed up before it would act up.

At a warm steady cruise @35mph under hard accell - WOT - the engine will rev to 3000rpm and hang there boost drops to 0psi until lift off the pedal - WOT the boost comes up and accells normal 3500 rpm and upshifts - This happens after warmup - runs normal cold - tried a Boost pressure sensor- Fuel press is 50psi at wot - EBP 37psi wot - ICP goes to 2850psi wot even at the failure - loosened exhaust at turbo - no difference - replaced turbo assy - same results - HPOP new - was loosing / dropping pressure on accell last month - would build to 1700 drop to 400 @ wot Outta ideas ? I retired working on these things and my former dealership is asking for help - I may have forgotten a few things but not the 6.0's I'm open to anything - Thanks in advance

Welcome back.

After leaving the dealer world in 2009 and I'm back. Boy have they changed LOL

I know it's hard to imagine doing something else, but the automotive industry is gigantic. The jobs are endless. It's also a great time to be job hunting. Employers are starving for good people. Good luck in your next venture. Joe

Look after your bodies gentlemen....you only have ONE. NOTHING in life is worth risking or compromising or your health.

Is the tone ring still on the old engine.

2014 Escape 1.6L 300k replaced what appeared to be the original timing belt, these tools worked great. Also repaired multiple oil leaks,new valve cover(PCV system problem),resealed HPFP & vacuum pump brackets. Massive Absolute Timing Tool Set 4pc Sigma Ford MASSIVESPEEDSYSTEM.COM PRO+ 4 Piece kit is designed specifically for the turbocharged Sigma engine family. Comes with Sprocket locker AND crank...

That's a tough one, hope your recovery goes good. I am 45 and only had one shoulder surgery so far, I know how you feel about changing jobs. The doctor asked me if I plan on doing this the rest of my life, kind of put me in shock because I don't know what else to do for a living.

The programing portion was quicker than the 22 minutes stated on the screen it was maybe 5 minutes. then wait he 10 minutes. I did use a very large usb drive 128GB

I hear you Steve. Keep going...New opportunities...down a slightly different path.

As I sit at home recovering from my 3rd surgery in 26 years at the same dealer as a tech. It’s bittersweet as my mind wants to keep going but the body says no more. The owners said they will come up with something for me. It’s definitely nerve racking leaving the position I’ve done for 30 years between 2 jobs. I’m only 47. so guys, take care of your body. The flat rate has ruined mine over the years.

I'm doing a super duty, how long did it take for the usb portion to finish?

I had a brief attempt with the tap but I was too scared of cutting too deep. They where packed in way tighter than any others I've had to deal with.

I had a similar problem with one that had a couple doubled up washers. I eventually broke them free with a long bent tip trans pick. Got them out with a 1/4" extension with some grease on the end.

I have used various cleaning tools but gun bore brushes seem to work well. What about using tap and adjustable holder to get the copper washer out?

I have completed a few of these. The ones here went right through with no issues. I will say that you have to follow the instructions closely. I think the completion words on the screen state complete then go away. Honestly I didn't have any issues

Have not had the misfortune of doing one of those yet. Is it on a superduty or escape?

I am doing recall 23C25 to replace the instrument cluster module. While doing the PMI, the FDRS instructs me to plug a usb drive into the laptop and then into the vehicle usb port. It seems like the usb software update does not finish even after 2 hours. Anyone having success with this recall?

Pretty sure somebody reused the washers on this truck, they supposedly have only been in there for 30,00km. Once I got them out you can see where they leaked. Went at it with a borescope and pick to clean around the washers, then was able to break them free. Probably why those 2 injectors got stuck so bad. The 3.5 brush ended up working pretty good for cleaning.

After replacement with new Ford engine have code P0016. Scope pattern normal on cam and crank. Check engine light with long crank. Im pretty sure this has been addressed before. Can someone kindly send me in right direction.

Hello, does any one have any tips on pulling out stuck injector copper washers? I had 2 injectors stuck, had to slide hammer them out but now the copper washers are stuck in the bore. I've made a little hook out of a coat hanger to try to lift it up but it is moving. Also does any one have suggestions for cleaning the injector bore, the shop manual does not show a brush, the 3.5 gtdi brush is close but not quite long enough.

I looked in our catalog. I would tend to agree with that. I noticed the price on it too. I can see why you are questioning it.

Yep, that's the one.